Ubiquiti UniFi Security Gateway (USG-3P) Dual-WAN Internet: Unterschied zwischen den Versionen
Zur Navigation springen
Zur Suche springen
(→Status) |
|||
Zeile 138: | Zeile 138: | ||
show configuration commands > config.txt | show configuration commands > config.txt | ||
cat config.txt | cat config.txt | ||
+ | |||
+ | =Vyatta= | ||
+ | Auf dem Route laeuft [https://en.wikipedia.org/wiki/Vyatta Vyatta]. Eine Dokumentenliste gibt es [https://docs.huihoo.com/vyatta/6.3/ hier]. |
Aktuelle Version vom 24. Februar 2024, 11:49 Uhr
Inhaltsverzeichnis
Allgemeines
Ich habe 2 ISPs. Einmal Kabel WAN1 (Vodafone 1GB/s) und einmal DSL16 WAN2 (1und1). Beide sind am USG (WAN1 Primary und WAN2 Secondary) angeschlossen und auf Fallback eingestellt.
Problem
Nach einem Ausfall des Kabelanschlusses hat das Fallback nur teilweise funktioniert. Die über LAN angschlossenen Geraete hatten tatsaechlich eine Verbindung ueber WAN2 erhalten, (ein Teil der) WLAN-Geraete nicht. Ein Reset der Kabelbox brachte zwar das Internet wieder zurueck, aber das USG schaltete nicht wieder zurueck auf WAN1.
Das Problem scheint bekannt. [1]
Status
Folgende Routen und Links habe ich bei mir mir aktivem Fallback sehen können.
Tibb@ubnt:~$ ip r
84.59.176.1 dev pppoe1 proto kernel scope link src 84.59.186.223
127.0.0.0/8 dev lo proto kernel scope link src 127.0.0.1
192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.2
192.168.2.0/24 dev eth1.2 proto kernel scope link src 192.168.2.1
192.168.148.0/24 dev eth1.148 proto kernel scope link src 192.168.148.1
192.168.178.0/24 dev eth1 proto kernel scope link src 192.168.178.1
Tibb@ubnt:~$ ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP
link/ether fc:ec:da:44:a5:3a brd ff:ff:ff:ff:ff:ff
inet 192.168.1.2/24 brd 192.168.1.255 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::feec:daff:fe44:a53a/64 scope link
valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN
link/ether fc:ec:da:44:a5:3b brd ff:ff:ff:ff:ff:ff
inet 192.168.178.1/24 brd 192.168.178.255 scope global eth1
valid_lft forever preferred_lft forever
inet6 fe80::feec:daff:fe44:a53b/64 scope link
valid_lft forever preferred_lft forever
4: eth2: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP
link/ether fc:ec:da:44:a5:3c brd ff:ff:ff:ff:ff:ff
inet6 fe80::feec:daff:fe44:a53c/64 scope link
valid_lft forever preferred_lft forever
5: imq0: <NOARP,UP,LOWER_UP> mtu 16000 qdisc pfifo_fast state UNKNOWN qlen 11000
link/void
8: eth1.148@eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP
link/ether fc:ec:da:44:a5:3b brd ff:ff:ff:ff:ff:ff
inet 192.168.148.1/24 brd 192.168.148.255 scope global eth1.148
valid_lft forever preferred_lft forever
inet6 fe80::feec:daff:fe44:a53b/64 scope link
valid_lft forever preferred_lft forever
12: eth1.2@eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP
link/ether fc:ec:da:44:a5:3b brd ff:ff:ff:ff:ff:ff
inet 192.168.2.1/24 brd 192.168.2.255 scope global eth1.2
valid_lft forever preferred_lft forever
inet6 fe80::feec:daff:fe44:a53b/64 scope link
valid_lft forever preferred_lft forever
24: pppoe1: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1492 qdisc pfifo_fast state UNKNOWN qlen 100
link/ppp
inet 84.59.186.223 peer 84.59.176.1/32 scope global pppoe1
valid_lft forever preferred_lft forever
Tibb@ubnt:~$ show load-balance status
Group wan_failover
interface : eth0
carrier : up
status : inactive
gateway : 192.168.1.1
route table : 203
weight : 0%
flows
WAN Out : 164
WAN In : 0
Local Out : 0
interface : pppoe1
carrier : up
status : failover
gateway : pppoe1
route table : 202
weight : 0%
flows
WAN Out : 56863
WAN In : 0
Local Out : 0
Tibb@ubnt:~$ show load-balance watchdog
Group wan_failover
eth0
status: Waiting on recovery (0/3)
pings: 3
fails: 3
run fails: 3/3
route drops: 1
ping gateway: ping.ubnt.com - DOWN
last route drop : Sat Feb 24 04:15:52 2024
pppoe1
status: Waiting on recovery (0/3)
failover-only mode
pings: 3
fails: 3
run fails: 3/3
route drops: 1
ping gateway: ping.ubnt.com - DOWN
last route drop : Sat Feb 24 04:15:53 2024
Tibb@ubnt:~$ show interfaces
Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
Interface IP Address S/L Description
--------- ---------- --- -----------
eth0 192.168.1.2/24 u/u WAN
eth1 192.168.178.1/24 u/u LAN
eth1.2 192.168.2.1/24 u/u
eth1.148 192.168.148.1/24 u/u
eth2 - u/u WAN2
lo 127.0.0.1/8 u/u
::1/128
pppoe1 84.59.186.223 u/u
Tibb@ubnt:~$ show ip route
Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF,
I - ISIS, B - BGP, > - selected route, * - FIB route
S> 0.0.0.0/0 [230/0] via 192.168.1.1, eth0
is directly connected, pppoe1
C>* 84.59.176.1/32 is directly connected, pppoe1
C>* 127.0.0.0/8 is directly connected, lo
C>* 192.168.1.0/24 is directly connected, eth0
C>* 192.168.2.0/24 is directly connected, eth1.2
C>* 192.168.148.0/24 is directly connected, eth1.148
C>* 192.168.178.0/24 is directly connected, eth1
Um alle Config-Einstellungen zu sehen.
show configuration commands > config.txt cat config.txt
Vyatta
Auf dem Route laeuft Vyatta. Eine Dokumentenliste gibt es hier.